碳酸盐岩风化吸收的大气CO2主要以HCO3-形式连续地经由河流从大陆输送到海洋,成为陆地生态系统的重要碳汇。目前主要河流流域的碳酸盐岩风化碳汇估算存在不确定性,分布格局尚不清晰。基于GEMS-GLORI全球河流数据库提供的全球10万km 2以上主要河流流域多年平均监测数据,利用水化学径流法估算出全球主要河流流域碳酸盐岩对CO2的吸收速率为0.43±0.15 Pg CO2 yr -1,平均CO2吸收通量为7.93±2.8 t km -2 yr -1。CO2吸收通量在不同气候带下差异显著,热带和暖温带CO2年吸收速率占全球主要河流流域年吸收速率的62.95%。冷温带CO2年吸收速率占全球主要河流流域的33.05%,仅次于热带地区。本文划分出全球CO2吸收通量的9个关键带,关键带的交汇处CO2吸收通量较高。喀斯特出露流域碳酸盐岩对CO2吸收通量的均值为8.50 t km -2 yr -1,约为非喀斯特流域的3倍。全球喀斯特出露流域碳酸盐岩风化碳汇在全球碳循环、水循环及碳收支平衡估算研究方面占据重要地位。 相似文献
Crack nucleation has been the subject of important contributions in the last two last decades. However, it seems that few attention has been granted to the case of saturated porous media. This is the question addressed in the present paper which is devoted to nucleation in traction mode. From a physical point of view, nucleation is a sudden phenomenon, so that the material response is both adiabatic and undrained. In the spirit of the variational approach, the nucleated crack is viewed as the final state of a region of space in which the material undergoes a full damage process. In traction mode, the opening of a saturated crack in undrained condition induces a drop of fluid pressure. In case of low fluid compressibility, the presence of the fluid delays the brittle failure usually associated with nucleation, as long as the fluid pressure remains above the saturation vapor pressure. Nucleation is therefore possible only if a partial vaporization of the fluid takes place. 相似文献
We analyzed the spatial local accuracy of land cover (LC) datasets for the Qiangtang Plateau, High Asia, incorporating 923 field sampling points and seven LC compilations including the International Geosphere Biosphere Programme Data and Information System (IGBPDIS), Global Land cover mapping at 30 m resolution (GlobeLand30), MODIS Land Cover Type product (MCD12Q1), Climate Change Initiative Land Cover (CCI-LC), Global Land Cover 2000 (GLC2000), University of Maryland (UMD), and GlobCover 2009 (Glob-Cover). We initially compared resultant similarities and differences in both area and spatial patterns and analyzed inherent relationships with data sources. We then applied a geographically weighted regression (GWR) approach to predict local accuracy variation. The results of this study reveal that distinct differences, even inverse time series trends, in LC data between CCI-LC and MCD12Q1 were present between 2001 and 2015, with the exception of category areal discordance between the seven datasets. We also show a series of evident discrepancies amongst the LC datasets sampled here in terms of spatial patterns, that is, high spatial congruence is mainly seen in the homogeneous southeastern region of the study area while a low degree of spatial congruence is widely distributed across heterogeneous northwestern and northeastern regions. The overall combined spatial accuracy of the seven LC datasets considered here is less than 70%, and the GlobeLand30 and CCI-LC datasets exhibit higher local accuracy than their counterparts, yielding maximum overall accuracy (OA) values of 77.39% and 61.43%, respectively. Finally, 5.63% of this area is characterized by both high assessment and accuracy (HH) values, mainly located in central and eastern regions of the Qiangtang Plateau, while most low accuracy regions are found in northern, northeastern, and western regions.
A FORTRAN program, consistent with the commercially available finite element (FE) code ABAQUS, is developed based on a three-dimensional (3D) linear elastic brittle damage constitutive model with two damage criteria. To consider the heterogeneity of rock, the developed FORTRAN program is used to set the stiffness and strength properties of each element of the FE model following a Weibull distribution function. The reliability of the program is assessed against available experimental results for granite cylindrical specimens with a throughgoing, flat and inclined fissure. The calibration procedure of the material parameters is explained in detail, and it is shown that the compressive to tensile strength ratio can have a substantial influence on the failure response of the specimens. Numerical simulations are conducted for models with different levels of heterogeneity. The results show a smaller load bearing capacity for models with less homogeneity, representing gradual coalescence of fully damaged elements forming throughout the models during loading. The maximum load bearing capacity is studied for various combinations of inclination angles of two centrally aligned, throughgoing and flat fissures of equal length embedded in cylindrical models under uniaxial and multiaxial loading conditions. The key role of the compressive to tensile strength ratio is highlighted by repeating certain simulations with a lower compressive to tensile strength ratio. It is proven that the peak loads of the rock models with sufficiently small compressive to tensile strength ratios containing two throughgoing fissures of equal length are similar, provided that the minimum inclination angles of the models are the same. The results are presented and discussed with respect to the existing experimental findings in the literature, suggesting that the numerical model applied in this study can provide useful insight into the failure behaviour of rock-like materials. 相似文献
The Yangtze River Economic Belt (YREB) spans three terrain steps in China and features diverse topography that is characterized by significant differences in geological structure and present-day crustal deformation. Active faults and seismic activity are important geological factors for the planning and development of the YREB. In this paper, the spatial distribution and activity of 165 active faults that exist along the YREB have been compiled from previous findings, using both remote-sensing data and geological survey results. The crustal stability of seven particularly noteworthy typical active fault zones and their potential effects on the crustal stability of the urban agglomerations are analyzed. The main active fault zones in the western YREB, together with the neighboring regional active faults, make up an arc fault block region comprising primarily of Sichuan-Yunnan and a “Sichuan-Yunnan arc rotational-shear active tectonic system” strong deformation region that features rotation, shear and extensional deformation. The active faults in the central-eastern YREB, with seven NE-NNE and seven NW-NWW active faults (the “7-longitudinal, 7-horizontal” pattern), macroscopically make up a “chessboard tectonic system” medium-weak deformation region in the geomechanical tectonic system. They are also the main geological constraints for the crustal stability of the YREB. 相似文献